Santa Rosa Reef is part of the U.S. territory of Guam and located about 25 nautical miles (46 km) south-southwest of
the island of Guam. It is a mostly flat-topped bank with one reaches as shallow as 7 m below sea level. Most of the
bank top is characterized by moderate relief, lots of algae, scattered corals and a few reef fish.
Optical validation data were collected using the Tethered Optical Assessment Device (TOAD), a sled equipped with
underwater video camera and lights. These data are used to provide ground-truth validation for benthic habitat maps
based on multibeam echosounder surveys. Camera sled deployments were conducted at night, usually between 1800 and
midnight. The duration of each tow varied but averaged about 40 minutes of bottom time at a given location. The camera
sled was deployed from the port J-frame mounted amidships on the NOAA Ship Oscar Elton Sette. At each station the ship
was positioned with the wind on the port side and drifted downwind; occasional light turns were applied to the ship's
screws if necessary to reduce the ship's motion. The TOAD was lowered slowly to the bottom by the deck crew using a
capstan. The operator monitored a live video feed from the camera and began recording data on a video tape recorder.
When the camera reached bottom the deck crew was notified by radio to stop lowering. The operator continued to monitor the
vehicle and provided commands to raise or lower it to keep the camera just above the bottom.
Equipment Description: The TOAD was deployed from the lower arm of the vessel's port side J-frame. The TOAD is a
camera sled based on the Guildline MiniBat model 8820 tow body. The frame has been extensively modified from its
original configuration and was equipped with an ROS model 54-00100-13 color underwater video camera as the primary
data collection instrument. The ROS camera was mounted to point at approximately a 45 degree angle toward the seafloor.
A Deep Sea Power and Light model 2050 MultiSeaCam low-light color video camera was also mounted on the sled and aimed
straight ahead. The signal from this camera was fed to a second video monitor to provide warning of underwater obstructions
the sled might be headed for. Illumination was provided by two 500 W DeepSea Power & Light Multi-SeaLite model 1050
underwater lights mounted on the original sled frame. The lights were located near the base and each side of the sled
to provide the maximum possible horizontal distance from the ROS camera. Cable between the sled and the surface consisted
of a underwater electrical cable (cable 2, black in color) with an internal kevlar strength member to support the sled frame.
The cable was led from the camera sled over a 22-inch diameter sheave hung from the J-frame, and from there around a
gypsy head mounted on the alternate CTD winch, amidships on the vessel's port side. All TOAD surface components were
located in the Dry Lab in an equipment rack on the after bulkhead.
Name & address of person collecting data:
1845 WASP Blvd., Building 176
Honolulu, HI 96818
Data Files: Video data were recorded on a video tape recorder. The position of the camera sled was recorded in WGS-84
using Guildline MiniBat In-Tow data acquisition software and a data feed from a shipboard Northstar Chartplotter.
File naming convention: Each tow is given a name consisting of a 3-letter designator for the island area followed by a
two-digit year and three-digit tow number, which increments by one for each new tow around that island. For Santa Rosa Reef the designator is "SRR."
During OES0308 (NOAA Ship Oscar Elton Sette's 8th cruise in calendar year 2003) the consecutive numbers started at SRR03001.
Video tape labels, the navigation files (*.glo) and paper log forms are annotated with the tow name and number, e.g.,
SRR03002. If the navigation file is edited during processing the file name has a suffix 'a' added. For example, for a
navigation data file named "SRR03002a.glo," the 'a' would indicate that metadata were extracted from the navigation data
and recorded to a file with the same name as the navigation file except that a file type of '.met' was appended; for
Time Correlation: All times are based on UTC. Two clocks were manually synchronized prior to starting data collection;
the clock in the video character generator that was used to annotate the video tape, and the clock in the TOAD data
acquisition computer. These clocks were set to UTC at the beginning of each evening's operations.
Resource Description: Digital video imagery that is geo-referenced to navigation files.